Please reference this page for helpful videos, images and text to help you take care of your vape pen.  Please send us an email or contact form if you have an idea for us to add to this page.

Using Your New Vape Pen, Electronic Cigarette Battery

Press the button 5 times in 2 seconds to turn on or off!

 How to charge?

ecigs, ecigarettes, electronic cigarettes, vaping supplies, vaping wands, vaping pens, ecigs NZ, ecigarettes NZ, Kiwi ecigs, electronic cigarettes new zealand, electronic cigarettes NZ, electronic cigarettes kiwi,electronic cigarettes auckland, ecigs new zealand, ecigs auckland, ecigarettes new zealand, ecigarettes auckland

Screw the battery as shown above onto our    EGo Rapid USB Chargers.

When charging your battery, simply screw the battery clockwise into the USB charger until the light on the charger changes from green to red. When the light is red, the battery is charging. The light on the charger will turn green when the battery is fully charged.

Important notes and safety precautions about charging your VAPE battery:

  • DO NOT OVER TIGHTEN THE BATTERIES ON THE CHARGER. Over-tightening the battery in the USB charger can cause the charger or battery to malfunction. Turn the battery slowly only until the light on the charger turns from green to red.

Vape Pen Battery Not Firing Against Coil (not vaping)

A fairly common, frustrating problem with vape pens can be that your firing pin in the top of the battery is not touching the metal part on the bottom of your (atomiser, cartomiser, or ) clearomiser tank. The battery needs to make contact with the metal portion of the tank so it can heat up the e-liquid. To fix this issue, you can take a toothpick and raise the battery firing pin up about 1mm, being very careful not to lift too hard. Gently circle the circumference of the pin lifting only about 1mm. This happens when you screw your  clearomiser tank on too tightly to your battery. Once you get the firing pin popped up more out of its socket, ref-fit your clearomiser to your battery. Screw the two units together until the thread grabs.  Plcae the mouthpiece to your ear, and depress the button. You should hear a crackling sound. Continue to slightly tighten, always checking for the crackle, until your units have a firm connection.   When attaching the battery to your charger, tighten only until the battery and charger lights show connection.

How to Fill an MT3 Clearomiser:

 

How to Clean an MT3 Clearomiser:

 

How to Fill a CE4 and CE4S Clearomiser:

 

How to Clean and Dry Burn a CE4 and CE4S Clearomiser:

 

 

 How to Clean and Fill a CE5+ Clearomiser:

How to use a Snoop Dogg G Pen Herbal Vaporiser

More videos coming….

 

Component Basics:

Batteries:
With the introduction of 1100mAH and 1300mAH batteries and even more powerful and compact batteries being tested, some of this is not as important as it used to be.  The Key to transitioning from tobacco to e-cigarettes is power and a clean atomiser.  If you run out of battery power while you’re out and about you’re screwed. Most chargers these days are USB powered and can be plugged into your car USB port or cigarette lighter port with a USB adapter found in the Accessories section.   An extended 8-10 blinking of your battery LED means it needs to be charged, 4-5 blinks means you’re over heating the atomiser, and it may switch off.

Don’t forget – If your battery seems dead, it may just be turned off.  Pressing the button 5 times in 2 seconds will turn it on.  Doing the same will turn it off.  If you hold the battery button in for 5 seconds, it will flash quickly and turn off.  This is a safety measure to save your equipment.

Flooding:
If you get a “gurgling” sound when you draw on your device, you have flooded the atomiser and/or the mouth piece “vapor chamber”.  This means that there is too much liquid in the atomiser for it to properly vaporize.  Remove the atomiser from the battery and cartridge and blow out the excess liquid onto a paper towel from the cartridge end.  Also blow out the cartridge from the mouth piece.

E-Liquid:
Some people new to vaping say that the flavors of the liquids are too faint or all taste the same.  Give it some time.  After being off tobacco cigarettes for a few days, your taste buds will start to recover and the flavors will become more distinct.  After a while, you’ll start to notice all of the subtle tastes and smells you’ve been missing all of this time!  If you like, you can change your flavors, or mix 1, 2 or more  for a different taste.

How to fill T3s / MT3s Bottom Fill Clearomiser:

Unscrew the bottom assembly from the tube
Hold the T3s / MT3s tube upside down with the drip tip facing down
Fill with 3ml E-Juice by tilting the clearomiser at a slight angle and dripping juice down the inside wall against the outer wall of clearomiser.
Do not put eliquid into the center tube as it will leak out the bottom of clearomiser.
Screw the bottom assembly back onto tube.
Screw onto electronic cigarette device and you’re ready to vape.

How to change the core/coil/head/ atomiser head on T3s and MT3s Bottom Fill Clearomiser:

Unscrew the bottom assembly from the tube
Remove the T3s / MT3s coil from the base and and simply screw a new coil into the base.
Screw base back onto T3s / MT3s Bottom Coil Clearomiser
Fill with 3ml E-Juice by tilting the clearomiser at a slight angle and dripping juice down the inside wall against the outer wall of clearomiser.
Do not put eliquid into the center tube as it will leak out the bottom of clearomiser.
Screw onto electronic cigarette device and you’re ready to vape.